This is a project I’ve been wanting to make for years. And as I admitted in my fall newsletter, I bought a pattern for one and it sat used for two years before I finally got around to testing it out. What resulted is something I constantly get compliments on (humble brag much?). It’s not the original vision I had for the jacket, but one that I love nonetheless. It’s the jacket I needed to make first so I could learn the pattern and the skills to make the next one even better. Plus I made it reversible, so two coats in one!

How to Make a Reversible Quilted Coat
Materials
- Fabric
- Approximately 2 yards of each the lining and outer fabric
- Bias tape
- Batting
- Thread
- All Well Cardigan Coat sewing pattern
Equipment
- Sewing machine
- Iron
- Scissors
- Pins
- Spray adhesive (optional)
- Masking tape (optional)
Directions
- Prepare fabric. After printing and cutting the pattern to your desired size, cut out the lining and top fabric.
- I made the un-cropped version which made it look like a cropped jacket! I also decided to curve the edges for a whimsical look. I followed size 3, large.


- Pin layers. Sandwich the top fabric and lining fabric with batting, right sides facing out. Use spray adhesive and/or safety pins to hold the layers together.


- Quilt fabric. Quilt the layers together with your desired pattern.
- I did simple straight lines running vertically. I used a strip of 0.75″ masking tape as a quilting guide. Lining it up against my presser foot meant by jacket was quilted with 1″ lines. I made the first quilting line down the center back and went left to right for the entire jacket.



- Hem the top of the sleeves and shoulders. With the outer fabric facing in, pin the layers together with unfolded bias tape. Sew the top of the sleeve and shoulder of the jacket on both sides with the bias tape. Trim the excess fabric once the bias tape has been sewed the layers together. Then fold the bias tape over to cover the raw edge and pin.
- Make sure to decrease the tension. You are sewing through two quilted layers aka four pieces of fabric and two pieces of batting.


- Fell the binding. Once the bias tape has attached the top seam (the sleeve and shoulder), sew the binding down flat. This will create the reversible jacket look.


- Hem the bottom of the sleeves and the sides. Sew the bottom of the sleeve and the side of the jacket (to the top of the curve) on both sides using bias tape to sandwich the layers and create a seam. Trim excess. Sew the binding flat on the side.
- Because of the arms, the binding cannot be sewed flat on the bottom of the sleeves, but this isn’t noticeable when you’re wearing the jacket. You could hand sew it flat if you desire.


- Bind the raw edges. Starting from the center back, sew bias tape along the bottom edge, go up the curve, wrap up the side (the opening of the jacket), around the neck, down the other side (the other opening), and join at the center back.
- This part should be significantly easier because it’s only one quilted layer instead of two.


- Create the pockets. Cut two 8 x 8″ squares of the lining fabric and two 8 x 8″ squares of the outer fabric. With rights sides facing each other, sew the lining and outer fabric together on one side. (This create the top seam of the pocket.) Turn right sides out and iron flat.
- Quilt the pockets. Cut two 8 x 8″ squares of the batting. Sandwich the batting in between the lining and outer fabric and quilt using 1″ vertical lines.
- Bind the pockets. Trim any excess batting and bind the three sides of the pocket with bias tape.
- My pockets measured 7″ x 7″ with rounded corners to match the rounded corners on the quilted coat.


- Attach the pockets to the jacket. Pin the pockets where you want them to be on the each side of the jacket. Sew the pockets to the jacket on the outer edge of the binding, getting as close to the edge as possible.
- My pockets were about 3″ from the sides and 1.5″ from the bottom. The quilting lines matched almost perfectly!


Pattern Review
I bought the All Well Cardigan Coat pattern from Amy and Amelia’s All Well creative studio. What I love about this pattern is it’s versatility and detailed guide, especially the hacking PDF to transform one pattern into multiple styles. You’re really getting your money’s worth of the $16 (it was $14 when I bought it, ya know, two years ago). I will say that I wish it had sleeves because the coat did turn out rather boxy with the batting, but the hacking guide does have a solution for that.
I made a large (size 3 in the pattern) so it would be oversized but this is actually a little small. It’s quite wide but the sleeves are WAY too short. I also followed the regular length of the jacket and it turns out quite cropped on me, just falling to the top of my hips. Make sure to add 6-10″ if you want this to be more of a coat. Next time I make this pattern I plan to make sleeves, lengthen the sleeves, have bigger pockets, and make it longer. I also might add a collar for a different look.
The simplicity of the pattern made it a great first foray into making clothes especially something as potentially difficult as a quilted coat. I just love the vintage teal fabric that can be dressed up or down. The jacket is cozy, washable and oh so cute. It’s a piece I wear all year round!
Happy sewing-

Pin for Later


Leave a Reply